منتجاتنا RFID
-
خط الصحافة زعنفة
-
يموت زعنفة
-
أدوات يدوية
-
قطع الغيار
-
زيت التبخر لمكبس الزعانف وثني الأنبوب
-
أنبوب المتوسع للمبادل الحراري
-
آلة إدخال الأنبوب الأوتوماتيكية ذات الزعانف
-
أنبوب بندر لمبادل حراري
-
فرن لحام بدرجة حرارة عالية
-
ثلاجة المبخر ماكينة
-
آلة فرن مبادل حراري
-
آلة لحام
-
آلة أنبوب النحاس العزل
-
آلة صنع تركيبات النحاس
-
لفائف بندر آلة
-
آلة بندر العودة
-
آلة تثقيب الأنابيب ذات التشفيه
-
آلة تنظيف بندر العودة
-
آلة لفائف الفطائر
-
آلة قطع الأنبوب
-
آلة حفر ثقب الأنبوب
-
أنبوب آلة ذوي الياقات البيضاء الصغيرة
-
آلة أنبوب متكامل
-
آلة إغلاق الأنبوب
-
آلة إدخال الحلقة
-
مبرد الهواء لوحة حافة آلة الانحناء
-
أنبوب النحاس وآلة الانصهار أنبوب الألومنيوم
-
آلة ثني الأنبوب
-
آلة تشكيل نهاية الأنبوب
-
معدات اختبار تسرب الهيليوم
-
آلة صنع حلقة اللحام
-
آلة ثني أنبوب السربنتين
-
آلة الغزل
أنبوب اعوج آلة الانحناء
ثلاجة أوتوماتيكية كاملة آلة ثني أنبوب الألومنيوموظيفة المعدات: 1. الآلة عبارة عن هيكل واحد من أصل عشرة ، أي ثني عشرة أنابيب في وقت واحد.
2. الآلة بأكملها تعتمد محرك سيرفو ، محرك هيدروليكي ومحرك هوائي.
3. يتم التحكم في نظام التحكم الكهربائي بواسطة شاشة تعمل باللمس PLC +. تتبنى PLC علامة Mitsubishi التجارية ، وشاشة تعمل باللمس تعتمد ماركة Taiwan Weilun ، والأجهزة الكهربائية ذات الجهد المنخفض تعتمد علامة Schneider التجارية. مبدأ العمل:
1. The pipe bender is mainly composed of discharging device, straightening device, primary feeding device, cutting device, secondary feeding device, bending device, table rotating device, rack and electric control device. The whole action is driven by oil cylinder and servo motor, and the electric appliance is controlled by PLC + touch screen. The pipe bender is developed by imitating the imported automatic pipe bender. The action steps and technological process are completely the same as those of the imported equipment, which is relatively reasonable.
2.Put the whole coil into the discharging rack, and lead the pipe end to the feeding clamp of primary feeding. Press the start button, the primary feeding device will send the pipe through the cutting device to the secondary feeding clamp. At this time, the primary feeding clamp returns to its original position, stops working, the secondary feeding clamp starts working, and the pipe is sent into the bending wheel to start bending. When bending to a certain length, cut off the pipe and continue bending until the final bending is completed, and take out the bent single piece manually. Press the start button again, the machine will repeat the above feeding elbow action, so as to cycle.
1. The pipe bender is mainly composed of discharging device, straightening device, primary feeding device, cutting device, secondary feeding device, bending device, table rotating device, rack and electric control device. The whole action is driven by oil cylinder and servo motor, and the electric appliance is controlled by PLC + touch screen. The pipe bender is developed by imitating the imported automatic pipe bender. The action steps and technological process are completely the same as those of the imported equipment, which is relatively reasonable.
2.Put the whole coil into the discharging rack, and lead the pipe end to the feeding clamp of primary feeding. Press the start button, the primary feeding device will send the pipe through the cutting device to the secondary feeding clamp. At this time, the primary feeding clamp returns to its original position, stops working, the secondary feeding clamp starts working, and the pipe is sent into the bending wheel to start bending. When bending to a certain length, cut off the pipe and continue bending until the final bending is completed, and take out the bent single piece manually. Press the start button again, the machine will repeat the above feeding elbow action, so as to cycle.
ريتا آلة المحدودة
جمع: No.2 Xinghengyizhi Road, Cicheng Industry Park, Jiangbei District, 315000, Ningbo City, Zhejiang Province, China
الهاتف: +86-574-81106661
البريد الإلكتروني: info@retamachine.com
الويب :www.retamachine.com
البحث ذات الصلة
- أنبوب اعوج آلة الانحناء
سابق زعنفة يموت القاطع